eye bolt lifting capacity chart

Eyebolts & Eyenuts - Grade 4 WLL Guide - Lifting Victoria

The new Australian Standard released for Grade 4 Collared Eyebolts and Eyenuts. AS2317.1: supersedes the old standard AS2317-1998. To help you work to the standard Townley have prepared a handy AS2317.1: Grade 4 Collared Eyebolts User Guide, which is

Learn More
What Are The Different Types of Eye Bolts Used for Overhead Lifts?

Shouldered eye bolts are also commonly referred to as "shoulder pattern" eye bolts. These eye bolts are designed with a shoulder at the point where the eye and the shank come together. This shoulder design reduces bending stresses on the shank and allows the eye bolt to be used for angular lifting if the shoulder is properly seated in the load.

Learn More
Lifting Eye Bolts | STS Industrial

Lifting Eye Bolt. ASTM A489 Type 1 Lifting Eye Bolts are forged, carbon steel threaded eye bolts intended for use with tapped holes that have been engineered as a lifting point. Dimensional specifications are governed by ASME B18.15 in sizes 1/4" through 2-1/2". According to ASME B30.26 - Rigging Hardware, each eye bolt shall be marked to show: 1.

Learn More
A Guide for Eye Bolts and Lifting Points - Types and Safe Use. - DLH Online

Use CAUTION when lifting. Any angle beyond vertical (axial lift ) will reduce the rating capacity refer to load charts. Eyebolts conforming to this standard are suitable for use at temperatures ranging from -20 °C to +200 °C without a reduction in their lifting capacity. Material identification symbol: C15 or C15E.

Learn More
M30 Eyebolts | McMaster-Carr

Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.. Powder-coated steel eyebolts are impact resistant, but less corrosion resistant than stainless steel eyebolts. They include a removable key for tightening the bolt.. Note: Capacities listed are for vertical lifting only. Eyebolts with shoulder can be used for angular lifting up to 45°, but the

Learn More
Metric Thread Collared Eyebolts to BS4278 - LiftingSafety

Safety Note: Eyebolts under M12 are not recommended for lifting. Various sizes from M6 to M80; Capacities (SWL - Safe working Load) from 100kg up to 30t 

Learn More
How Much Weight Can An Eye Bolt Hold? [ANSWERED] - Lift-All Company

However, at just 15 degrees, the weight capacity is reduced by 20%. For example, an eye bolt with a 1/4 inch shank can typically hold up to 600 pounds at a straight pull (no angle). However, at a 15 degree angle, the maximum weight capacity drops to 480 pounds (80% of the "straight pull" weight capacity).

Learn More
Best Practices When Using Lifting Eye Bolts | G.L. Huyett

2021. 6. 24. · Practices to avoid when using lifting eye bolts: Running a Sling Through Eye Bolts. It's often convenient to run a sling through a pair of eye bolts, however, it should be avoided. Attaching a sling in this manner applies angular force to the eye bolts and, as we mentioned earlier, angular forces drastically reduce a lifting eye bolt's WLL.

Learn More
Confused By Eyebolt Standards? Let's clear it up. - LGH

Let's clear it up. - LGH. In 1960, when ANSI first published the B18.15 standard on forged eyebolts, they stated "that it would be impossible to develop an ANSI standard which would agree with even a small percentage of the standard products (eyebolts) being produced.". This forced them to attempt to come as close as possible to an

Learn More
LIFTING EYE BOLTS - NET

See Safe Lifting Chart on page 5. All rated capacities consider a straight vertical lift. Use CAUTION when lifting. Any angle beyond vertical (zero degree) will 

Learn More
Eyebolts & Eyenuts - Grade 4 WLL Guide | Lifting & Rigging

NOTES: The included angle, between the legs of every two-leg sling connected to a load by a pair of eyebolts or eyenuts, should not exceed 90 degrees.

Learn More

Leave a comment